A 40x60 pole barn in north Missouri runs roughly $50,000 for a bare shell and roughly $100,000 finished with a concrete floor under it.
That is not a vague spread. It is two different buildings, and the gap between them is almost entirely one line item. On our own 40x60 quotes the concrete has come to about 40% of the finished price — more than all the building materials, more than all the labor.
Which is also the answer to the question underneath the question. When two quotes for “a 40x60” come back $40,000 apart, they are usually not the same building.
The three prices of the same barn
A 40x60 is 2,400 square feet of floor. Here is what ours have come out at, built the same way, at three different points of finish:
| What you are buying | Per square foot | On a 40x60 |
|---|---|---|
| Bare shell — posts, trusses, purlins, metal, trims, one walk door | about $21 to $24 | low fifties |
| Weathertight — shell plus overhead doors and gutters | about $29 to $33 | low to mid seventies |
| Finished — all of the above plus slab, footings and dirt work | about $40 to $45 | $95,000 to $107,000 |
Those are our numbers on our jobs, in 2026, within an hour or so of Jamesport. A real quote still needs somebody standing on the ground it is going on.
The slab is the biggest single thing on the page
Most people budget for the building and treat the concrete as a detail. It is the other way round.
And “concrete” is not one product. On a 40x60 we have quoted all three of these:
- Floor only, 4 to 6 inches with rebar — roughly $20,000 to $23,500.
- Floor plus piers under each post, usually 26 to 28 of them — roughly $29,000 to $31,000.
- Floor plus a full frost footing around the perimeter, 12 inches by 36 deep, with foam — roughly $36,000 to $40,000.
Read those again, because the gap is the whole point. A slab with a proper frost footing costs about a quarter to a third more than the same slab on piers — and on our quotes the frost-footed version had a thinner floor than the pier version and still cost more. The footing detail matters more than the inches of concrete.
Going from a 4 inch floor to a 6 inch floor is about 20% on the concrete line. Real money, but nothing like the footing decision.
So when you compare two barn quotes, find the concrete line first. If one says “5 inch floor with piers” and the other says “5 inch floor, 12x36 frost footing, foam, 45 ton of rock,” you are looking at a $10,000 difference before anybody has been dishonest about anything.
Overhead doors are the second biggest swing
A door is not a door. Off our own quotes, installed:
- A plain 10x10, no insulation, no opener — about $2,200.
- A 16x7 steel panel with an opener — about $3,600 to $3,800.
- A 12x12 insulated with an opener — about $4,800.
- A 12x14 insulated with an opener — about $5,400.
- A 16x16 with extra wind bracing — about $9,800.
One door, four and a half times the price, depending on how big it is and what is in it. Size drives that more than insulation does. Two 16x16 doors on a 40x60 can come to more than the trusses and the gutters put together.
It is worth being honest with yourself about what actually has to go through the opening. A 14 foot door swallows nearly everything on a farm. A 16 is for a specific machine, and you should know which one.
What else moves the number
- Eave height. A 12 foot wall and a 16 foot wall are not the same building with four feet added — the posts, the sidewall metal, the girts and the doors it will take all change together. We price it per job. Tell us what has to fit inside and we will tell you the height.
- Truss type. A scissor truss, which gives you a vaulted ceiling instead of a flat one, runs about 27% more than a standard flat-bottom truss on our quotes.
- Gutters. Around $10 to $12 a foot installed, and a 40x60 takes somewhere north of 200 feet. Call it $2,000 to $2,800.
- Dirt work. A normal pad and a driveway runs $3,700 to $4,500. If the site needs real reshaping or fill hauled in, that number has no ceiling — we have seen it into five figures on other jobs.
- How far it is from Jamesport, and whether a concrete truck and a lift can get to the pad.
- Steel prices. They move, and a quote from spring is not a quote for fall.
The one that surprises people: bigger is cheaper per foot
Our build labor on a 40x60 runs around $7 to $8 a square foot. On a building over 5,000 square feet it falls nearer $5 to $7.
Same crew, same work, fewer setups per foot of floor. So if you are torn between a 40x60 and a 40x80, the extra 800 feet costs less per foot than the first 2,400 did. It is the one place in this whole article where spending more is also spending more efficiently.
The reverse is also true, and worth saying: a very small building carries its fixed costs on very few square feet. There is a lift rental on a 40x60 whatever happens — $2,250 on ours, every time.
What is in our quote, and what is not
In, as standard: posts, trusses, purlins, girts, roof and sidewall metal, all trims, a walk door, the lift, and the labor to put it up.
Not in, unless you ask and we price it:
- Concrete, footings and piers
- Dirt work, the pad and the driveway
- Overhead doors
- Gutters
- Insulation
- Electric to the building, and anything inside it
- Plumbing, heat, finished walls
None of that is us being clever. It is that those lines move so much between one site and the next that putting a guess in the quote would make the quote worse, not better.
Where people get burned, both directions
Against a cheap quote: the number that came in $30,000 under everybody else is usually a shell quote sat next to finished quotes. Before you compare two prices, compare the two lists. Ask specifically about the concrete, the doors, the gutters and who is doing the dirt work. Ask whether the builder carries insurance, and ask what happens to your deposit if the job slips.
Against us, and everybody like us: a quote that lists all of that looks higher on paper than one that does not, and it is not. It is the same barn with the truth typed out. We would rather lose a job on a number we can stand behind than win one on a number that grows after you have signed.
One more local thing: most of the counties we build in have no county building permit for a barn like this at all. We have written that up here. It means nobody is coming to check the footing depth on your behalf, which puts it back on you to ask.
What we would actually do
If it were ours:
- The pad and the slab get done properly first, and the building gets sized around what is left. The concrete is the part you cannot change afterward, and it is the part that decides whether the posts are still plumb in twenty years.
- A foot taller than seems necessary, if the budget takes it. Height is cheap on the day and impossible later.
- The door sized for the machine you actually own, rather than the biggest one on the page.
- Then whatever is left goes on the shell. If something has to give, it gives on finish, not on footings.
And if a 40x60 is more building than the job needs, we will say so. A 30x50 done right beats a 40x60 built to a number.
Ones we have built at this size
- A 40x60 shop at Warrensburg with a 12x60 open lean-to down each side, insulated doors and 6 inch gutters.
- A 40x60x14 garage at Edgerton in burnished slate with a rooster cupola on top.
- A garage and finished office at Hamilton — what one looks like when the inside gets finished out.
Call us and we will come and look at it.